How to FORMAT HARD DISK of my instrument (models with a SINGLE COLOR TFT DISPLAY)

ROVER meters, using the latest technology where the hardware is looking more and more like a computer. For this reason, in the event of loss of TV & SAT Memory Plans, should be performed "FORMAT HARD DISK" to clean the memories, before reloading the TV & SAT Memory Plans.

Below we listed the procedures for "FORMAT HARD DISK" valid ONLY for models with SINGLE DISPLAY COLOR:

PREREQUISITES:
Before carrying out the procedure "FORMAT HARD DISK", make sure you have accomplished all the following points:

1) Being already registered in the ROVER web site area "Update SW";

2) If you are already registered, run directly the "Login" typing your "Username" and "Password";

3) Download in the desktop of your PC, the interface program ROVER-S.M.A.R.T. PRO;

4) Install the ROVER-S.M.A.R.T. PRO interface program in your PC (only the first time);

N.B.: If the ROVER-S.M.A.R.T. PRO interface program is already installed in your PC, check that it is the LATEST version and always delete the old one;

5) Select the exact model of your Instrument and click "Click here";

  • Download on the desktop of your PC the file Update SW;
  • Download on the desktop of your PC the TV and SAT Memory Plans.

 

FORMAT HARD DISK - Only for this models:

EASY METER Series, HD TAB 4 Series, HD LIGHT, HD COMPACT, HD TAB 7 Series, HD FLASH, HD TAB 9 and HD PRO Series

For other models scroll down the page

WARNING: The following porcedure erases the memory of the instrument. At the end, you will have to reload the Instruments Software and TV and SAT Memory plans.

1) Switch-on the Instrument (press once the red button ROVER_HOME_RESETROVER_HOME_RESET to display on the screen the main HOME MENU);

2) Press and HOLD for at least 10 seconds SIMULTANEOUSLY the 3 mechanical buttons, SPECT, PLAN and VOLUME and wait until on the Instrument appears the menu shown in Figure 1;
ROVER FORMAT HARD DISK menu 2014 EN ROVER_RESUME_CALIBRATION
Figure 1: Menu selection
"FORMAT HARD DISK"
Figure 2: Menu selection
"RESUME CALIBRATION"
3) Select "FORMAT HARD DISK" (Figure 1), press the encoder (ENTER) and wait for the execution of the process;
4) Select the "RESUME CALIBRATION" (Figure 2), press the encoder (ENTER) and wait for the execution of the process;
5) When the process is completed switch-off the instrument;
6) Switch-on the Instrument and immediately after press and hold the VOLUME button until the completion of the start-up function, on the bottom right point of the screen, you will see a red square;

7) Load the SW (previously saved on the desktop of your PC);

8) Switch-off the Instrument;
9) Switch-on the Instrument and immediately press and hold the VOLUME button until completion signaled by a BEEP, after release the button;

10) Load the TV and SAT Memory Plans (previously saved on the desktop of your PC);

11) When finished, switch-off the Instrument and switch-on again after 10 seconds to verify proper operation.
 

FORMAT HARD DISK - Only for this models:

ATOM LIGHT Series, ATOM POWER, DIGICUBE, TOUCHMETER and HD TOUCH

WARNING: The following porcedure erases the memory of the Instrument. At the end, you will have to reload the Instruments Software and TV and SAT Memory Plans.

1) Switch-on the Instrument (press once the red button ROVER_HOME_RESETROVER_HOME_RESET to display on the screen the main HOME MENU);

2) Press and HOLD for at least 10 seconds SIMULTANEOUSLY the 2 mechanical buttons, SPECT and VOLUME and wait until on the instrument appears the menu shown in Figure 1;
ROVER FORMAT HARD DISK menu 2014 EN ROVER_RESUME_CALIBRATION
Figure 1: Menu selection
"FORMAT HARD DISK"
Figure 2: Menu selection
"RESUME CALIBRATION"
3) Select "FORMAT HARD DISK" (Figure 1), press the encoder (ENTER) and wait for the execution of the process;
4) Select the "RESUME CALIBRATION" (Figure 2), press the encoder (ENTER) and wait for the execution of the process;
5) When the process is completed switch-off the Instrument;
6) Switch-on the Instrument and immediately after press and hold the VOLUME button until the completion of the start-up function, on the bottom right point of the screen, you will see a red square;

7) Load the SW (previously saved on the desktop of your PC);

8) Switch-off the Instrument;
9) Switch-on the Instrument and immediately press and hold the VOLUME button until completion signaled by a BEEP, after release the button;

10) Load the TV and SAT Memory Plans (previously saved on the desktop of your PC);

11) When finished, switch-off the Instrument and switch-on again after 10 seconds to verify proper operation.


Company & contacts Products & APP Information Contacts