HD TAB 4-7 and 9: Partial block and various malfunctions and/or loss of some SATELLITES and TV PLANS

CAUTION:

The partial block and various malfunctions of the instrument, can occur rarely because of a continuous incorrect Switch-off. Basically if you usually hold down the RED button ROVER_HOME_RESETROVER_HOME_RESET for more than two seconds (eg 6 or 7 seconds) in some rare cases it may conflict with the "RESET HW" (forced shutdown); while the instrument, (which is in his switch off phase) is still saving the data in memory.

CORRECT switch-off of ROVER Instruments:

  • Press and hold the red Button ROVER_HOME_RESETROVER_HOME_RESET, the instrument emits immediately a first BEEP and, at the second BEEP ( approximately after 2 seconds) immediately release the red button ROVER_HOME_RESETROVER_HOME_RESET (even if the display is still active and shows the instructions for battery charge).

CAUTION:

  • Do not hold the red button ROVER_HOME_RESETROVER_HOME_RESET after the second BEEP, to avoid starting the HW RESET function (forced shutdown). Basically, every time you switch-off, the instrument needs about ten seconds to save the data in memory before switching off, if for every switch-off, accidentally you activate the HW RESET function (forced shutdown) there is the possibility to corrupt the data in memory.

However, if the instrument is partially blocked, you have to do the "FORMAT HARD DISK" and then reload the SW and the memory plans with your PC as per instructions listed below:

 FORMAT HARD DISK

PREREQUISITES: Before carrying out the procedure "FORMAT HARD DISK", make sure you have accomplished all the following points:

1) Being already registered in the ROVER web site area "Update SW";

2) If you are already registered, run directly the "Login" typing your "Username" and "Password";

3) Download in the desktop of your PC, the interface program ROVER S.M.A.R.T. PRO;

4) Install the ROVER S.M.A.R.T. PRO interface programin your PC (only the first time);

N.B.: If the ROVER S.M.A.R.T. PRO interface program is already installed in your PC, check that it is the LATEST version and always delete the old one;

5) Select the exact model of your Instrument and click "Click here";

  • Download on the desktop of your PC the file Update SW;
  • Download on the desktop of your PC the TV and SAT Memory Plans.

Now we can accomplish the "FORMAT HARD DISK” PROCEDURE

WARNING: The following porcedure erases the memory of the instrument. At the end, you will have to reload the Instruments Software and TV and SAT Memory Plans.

1) Switch-on the instrument (press once the red button ROVER_HOME_RESETROVER_HOME_RESET to display on the screen the main HOME MENU);

2) Press and HOLD for at least 10 seconds SIMULTANEOUSLY the 3 mechanical buttons, SPECT, PLAN and VOLUME and wait until on the instrument appears the menu shown in Figure 1;
ROVER FORMAT HARD DISK menu 2014 EN
ROVER_RESUME_CALIBRATION 
Figure 1: Menu selection
"FORMAT HARD DISK"
Figure 2: Menu selection
"RESUME CALIBRATION"
3) Select "FORMAT HARD DISK" (Figure 1), press the encoder (ENTER) and wait for the execution of the process;
4) Select the "RESUME CALIBRATION" (Figure 2), press the encoder (ENTER) and wait for the execution of the process;
5) When the process is completed switch-off the instrument;
6) Switch-on the instrument and immediately after press and hold the VOLUME button until the completion of the start-up function, on the bottom right point of the screen, you will see a red square;

7) Load the SW (previously saved on the desktop of your PC);

8) Switch-off the instrument;
9) Switch-on the instrument and immediately press and hold the VOLUME button until completion signaled by a BEEP, after release the button;

10) Load the TV and SAT Memory Plans (previously saved on the desktop of your PC);

11) When finished, switch-off the instrument and switch-on again after 10 seconds to verify proper operation.

  • Click here if you want to download this "F.A.Q." in pdf format.


Company & contacts Products & APP Information Contacts